Publications

Showing 1651 - 1675 of 1703 results
Electric drills vary in noise output according to type. Hammer drills produce the highest noise levels because of their impact function. The quality and method of construction of the drill also...
WorkSafe
Fact sheet
14 May 2014
Angle grinders are used extensively in the metalworking and panel beating areas and can be used for wood carving when equipped with an "Arbortech" woodcarving disc. Other accessories such as...
WorkSafe
Fact sheet
14 May 2014
Hand held belt sanders range in noise level from 92 to 103 dB(A). The noise levels are directly affected by the quality and condition of the tool. The free running noise level of a belt sander is...
WorkSafe
Fact sheet
14 May 2014
Orbital sanders range in noise level quite dramatically, the quietest currently being the Festo and ELU brands (80-82 dB(A)). The noise levels are directly affected by the quality and condition of...
WorkSafe
Fact sheet
14 May 2014
Challenging behaviour is any behaviour that causes significant distress or danger to the person of concern or others. It can include an outburst of aggression, or resistant type behaviour by clients...
WorkSafe
Guide / handbook
14 May 2014
The cost of building a house can be affected by the nature of the site. It is wise to investigate the suitability of the site before selecting a block of land. When choosing a block When selecting a...
Building Commission
Fact sheet
14 May 2014
When carrying out ‘builder work’ for another person, in most parts of Western Australia registration as a building contractor is required. What is ‘builder work’? ‘Builder work’ is building work: for...
Building Commission
Fact sheet
14 May 2014
This educational article has been developed to assist in the identification of occupational safety and health (OSH) hazards. The hazard identification tools were developed following interviews with...
WorkSafe
Fact sheet
13 May 2014
Information about using electricity safely near water.
EnergySafety
Brochure
13 May 2014
A report into the wild fire that occurred at Location 745 Bates Road, Dalyup, about 20 km west of Esperance, on Thursday 2 December 2005.
EnergySafety
Reports
12 May 2014
This application form is for an electrician's licence or electrician's licence endorsed 'electrical fitting work only' for interstate or New Zealand applicants under mutual recognition.
EnergySafety
Form – application
05 May 2014
This application form is to be used by a person holding an electrician's licence endorsed 'electrical fitting work only,' wishing to upgrade to a full electrician's licence.
EnergySafety
Form – application
05 May 2014
This application form is for an electrical worker's electrician's provisional Licence to work under supervision.
EnergySafety
Form – application
05 May 2014
This application form is used to apply for a ground geophysical survey equipment permit.
EnergySafety
Form – application
05 May 2014
This application form is used to apply for a restricted electrical worker's licence for interstate or New Zealand applicants under mutual recognition.
EnergySafety
Form – application
05 May 2014
This application form is used to apply for a refrigeration and airconditioning mechanics licence where the qualifications were gained overseas.
EnergySafety
Form – application
05 May 2014
This application form is used to apply for a mobile mining permit.
EnergySafety
Form – application
05 May 2014
This application form is used to restore a name to the Electrical Licensing Register.
EnergySafety
Form – application
05 May 2014
This form is used to notify Energy Safety of a change of name to an electrical worker's licence, permit, or certificate of registration and obtain an updated licence card.
EnergySafety
Form – application
05 May 2014
Notice of termination by park operator or tenant agreement frustrated Form 2011
Consumer Protection
Form – notification
04 May 2014
Residential Parks condition report site only agreement
Consumer Protection
Reports
04 May 2014
This application form is used to advise Energy Safety of a lost or stolen gasfitting permit or gasfitting authorisation and apply for a replacement card.
EnergySafety
Form – application
02 May 2014
This application form is used to apply to restore your name to the gasfitting licensing register.
EnergySafety
Form – application
02 May 2014
This application form is used to notify Energy Safety of a change of name to your gasfitting permit or gasfitting authorisation.
EnergySafety
Form – application
02 May 2014
This is what an electrical safety certificate looks like. You should receive one from your electrical contractor within 28 days of the electrical work (other than repairs) being done.
EnergySafety
Information
02 May 2014

Pages